Difference between revisions of "Pathloss 5 - Revision history"
| Line 1: | Line 1: | ||
| + | == Pathloss 5 - revision date January 18, 2013 == | ||
| + | |||
| + | Fixed bug preventing the datum-projection information from being saved to the pl5 file when using the Pathloss 5 Link Program. | ||
| + | |||
== Pathloss 5 - revision date January 9, 2013 == | == Pathloss 5 - revision date January 9, 2013 == | ||
Revision as of 15:47, 18 January 2013
Pathloss 5 - revision date January 18, 2013
Fixed bug preventing the datum-projection information from being saved to the pl5 file when using the Pathloss 5 Link Program.
Pathloss 5 - revision date January 9, 2013
Added provision for Pathloss option files to be saved in the program directory. This may be necessary for some Windows Vista/7 configurations.
When adding SRTM data, the user was presented with a datum caution message for every file. Now only one message per batch is shown.
Update to Network toolbar.
Minor bug fixes regarding saving options to .ini files.
Pathloss 5 - revision date December 7, 2012
GIS Configuration
The System 1992/19 projection for Poland has been added. This is located under the European projections.
A geographic grid centered north and south on the equator could cause the network display to fail.
Cvt24_8.exe
This utility program now re-samples Tiff image files. Using a 50% reduction and conversion to a paletted image, a 200 Mbyte file can be reduced to 17 Mbytes. Several sampling algorithms are provided which effectively produce the same results.
Manual entry of adaptive modulation data
The following problems could occur in adaptive modulation radios which do not have a radio data file:
- the RX threshold and maximum receive signal values could be interchanged
- the maximum receive signal was not transferred from a lookup table
Pathloss 5 - revision date November 26, 2012
Optimization without radio data files did not transfer the TX power to the link
Link design rules
The following options are available in the Vigants-Barnett reliability method in the link design rules:
- Automatically determine the Climatic factor - calculate terrain roughness and C Factor
- Automatically determine the C factor
The following options have been added:
- Specify the Climatic factor - calculate terrain roughness and the C factor
- Specify the C factor directly
- Automatically determine the Dispersive fade occurrence factor
- Specify the Dispersive fade occurrence factor
Terrain Data
south African .ort files can now be converted and used with variable standard meridian.
Pathloss 5 - revision date November 13, 2012
Interference calculations on networks which include rectangular passive repeaters has been revised.
The antenna structure record (ASR) did not print on the Transmission summary detail or CSV reports. This was a side effect of the addition of height above average terrain in a previous build
Operations - Frequency Assignments
The high - low assignment correctly ignores passive repeaters.
Automated design using Adaptive modulation radios
The color coding on the automated design displays showed the results for the lowest modulation level instead of the reference modulation level.
Reflective plane definition
If the site 2 antenna height was at the minimum antenna height, the program could crash under some conditions.
Pathloss 5 - revision date October 30, 2012
Corrected bug in Edit-Modify Links Operation. If a pl5 profile had been reversed when imported in to the network, running Edit modify on this link would result in a loss of synchronization between the pl5 file and the gr5 file.
This would manifest in the "Pathloss File Data Discrepancies" dialog. All the site parameters will be swaped. To correct this error, it is necessary to delete the link in the network display (do not delete the file) and then re-import the pl5 file again from the Site List.
Pathloss 5 - revision date October 29, 2012
PTMP link design
Clicking on a point to multipoint link without an existing file association will automatically design the link using the base station equipment specifications. If the terrain database is configured, the profile will also be automatically generated.
Frequency assignments
Operations - Frequency assignments has a new option that will set the design frequency to the average frequency in the channel table. The design polarization will be set to the channel table polarization table for a single channel assignment or to the highest polarization usage for multiple channels. The default polarization is vertical.
When the channel table is edited in the Transmission analysis design section, a prompt is issued to update the design frequency and polarization using the above criteria.
Text import
Tower type import now accepts the tower type names (As they appear in the CSV report)
GIS datum selection
Changing only the datum in the PL50 link program did not save the changes in the associated pl5 file.
Pathloss 5 - revision date October 24, 2012
PTMP links created or modified using the automated link design features
If discrete channel assignments have been entered in the base station sectors, PTMP links created using the automated design features will set the design frequency to the average of the mobile and base station sector transmit frequencies. The design polarization will also be set to the sector polarization.
Link files which were exported in pl4 format could not be changed between microwave and VHF-UHF applications or vice versa in the version 4 Pathloss program.
Setting the local study extents resulted in an opaque circle if the Show local study extents option was not checked
Passive repeaters using back to back antennas
The passive repeater report had several lines out of sequence
Pathloss 5 - revision date October 12, 2012
4 Band GeoTIFF files (National Map Viewer Orthoimagry) can now be used.
Fixed bug which could cause a crash when closing the Projection parameters dialog from within the DEM text import dialog.
Pathloss 5 - revision date October 1, 2012
AntRad
The conversion from version 4 ASCII raf files to version 5 ASCII raf files did not allow the conversion to use separate directories for the version 4 and 5 files.
Height above average terrain (HAAT)
HAAT is now a site data parameter. This is an effective HAAT using the average value determined from a user specified path length, number of points and number of uniformly spaced radial profile.
The calculation is carried out in any of the design sections. Click on the site name on the status bar to access the site data entry form and the click the blue arrow on the HAAT data line to carry out the calculation.
Note that the HAAT definition does NOT include the antenna height. It is defined as the site ground elevation minus the average elevation.
Empirical studies
All calculations are based on the per radial height above average terrain.
Link text import
The design polarization will use the channel polarization if this is unique; otherwise, the default polarization will be used.
GIS Configuration
DEM files obtained from EarthExplorer.USGS.gov which used different cell sizes in the north-south and east-west directions at latitudes above 50 degrees (e.g 3 arc seconds NS and 6 arc seconds EW) did not correctly set the edges in the GIS file index
Area studies
Clicking cancel on a base station edit could invalidate an area study.
Pathloss 5 - revision date September 17, 2012
Added option to hide the local study radius. Configure - Options - Network display options - Axis-mapgrid - Show local study extents.
Adaptive modulation radio data files with 9 or 10 modulation states could cause a program instability in local and area study calculations. If the problem persists, it will be necessary to erase the following line in the windows PL50.INI file.
CLRMP_SCHEME_DATARATE_RSS_00=12,default.......
This line is in the [COLOR_RAMP_SCHEMES] section
Pathloss 5 - revision date September 6, 2012
SDH radio calculations (SES, unavailability, SESR and BBER) using space diversity could result in a program crash.
Rain Calculations
The options for the specific regression coefficients for ITU-R P.838-1 or -3 were not saved.
The ITU-R P.530-8/13 rain algorithm uses different equations for latitudes above and below 30 degrees. The transition between regions can result in a significant discontinuities.
ITU-R P.530-14 is now available with a new algorithm which does not depend on latitude. The implementation in the Pathloss program does NOT follow the ITU documentation for the effective path length calculation.
- The distance factor r is calculated (r < 2.5)
- Effective path length = actual path length x r (ITU)
- Effective path length = actual path length / r (Pathloss)
This change was made to provide a reasonable agreement between the results of the 530-8/13 algorithm at latitudes greater than 30 degrees.
At latitudes below 30 degrees, there are significant difference between 530-8/13 and 530-14
The rain calculation now includes three options for the ITU rain algorithm
- ITU-R P.530-7 - this is the same as ITU-R P.530-8/13 for latitudes above 30 degrees
- ITU-R P.530-8/13 this uses different algorisms above and below 30 degrees latitude
- ITU-R P.530-14
Land mobile location variability
Terrain classifications for bare trees, evergreen deciduous and rain forest were not included in the location variability calculation
Pathloss 5 - revision date August 10, 2012
NLCD 2001 /2006 Clutter
A new option has been added to the NLCD 2001 /2006 clutter model for the Hawaiian islands. Each of the 3 NLCD clutter models (CONNUS, Alaska and Hawaii) use an Albers equal area conic projection with different parameters.
Therefore in the GIS clutter configuration, only one type can exist in the file index. Separate GIS configuration files (p5g) must be used for the CONNUS, Alaska and Hawaiian clutter categories.
Maximum EIRP
In the frequency range from 5725.0 to 5875.0 the maximum ERIP was limited to 36 dBW. This figure was applicable for point to mulitpoint systems. For point to point radios the limit is now 53 dBW.
Example file directories
The example network files have been changed to refer to the current default installation directory c:\plw50 from the older c:\program_files\pathloss 50.
Pathloss 5 - revision date July 25, 2012
AntRad
Loading a version 4 ASCII (raf) file could lead to a corrupted capacity entry if the value did not exist in the file.
Saving a version 4 ASCII (raf) file could result in a corrupted frequency stability (ppm) if the value did not exist in file.
Error handling
The Yes to All option has been added to error messages in an interference calculation when the user is prompted to continue the operation when an error occurs.
This has also been added to the convert pl4 files to pl5.
Interference Calculations involving adaptive modulation radios
If a specific TX emission or RX selectivity curve is not available for the reference modulation state, the standard microwave TX emission or RX selectivity curves will be used.
Pathloss 5 - revision date July 23, 2012
The elevation field and easting/northing in the site list table did not allow a zero or a negative value to be entered.
Older adaptive modulation pl5 files which were created before the recent changes to adaptive modulation did not load correctly
Pathloss 5 - revision date July 18, 2012
PTMP links from base station. Adaptive modulation details are now displayed. It is not possible to select the modulation states as is the case in point to point links.
Interference calculations using version 4 pl4 files which contained a passive repeater could cause a program crash.
Edit modify links - If tx lines are included in the scope of the design and and the TX line length is not included, the TX Line loss will be removed.
Pathloss 5 - revision date July 12, 2012
Adaptive Modulation
Additional changes to the display and and reports.
Adding an adaptive modulation from from a lookup table follows the same procedure as adding the file from the radio file index.
Transmission analysis
The results display in the transmission analysis design section was corrupted for adaptive modulation applications
Interference calculations
Interference calculations on a point to multipoint network would generate invalid interference cases between links in the same sector.
The Hi-Lo violation report can now be generated when no interference cases have been calculated
The fade correlation display graphically shows the interference path with an curved line and arrow. On networks which cover a small area in the order of several kilometers, the path was off the display.
Create PTMP links
This operation did not add the correct sector number to the pl5 file. In an interference calculation this led to invalid interference cases
Antenna data files
The maximum size of an antenna data file is 47 characters. Antenna file names over 40 characters could cause a program crash in the Antenna data viewer.
ANT_RAD Version 4 radio data files
Clicking the Save mrs file (binary) menu item multiple times in succession would corrupt the mrs file.
Pathloss 5 - revision date June 21, 2012
NOTE
FILES CREATED WITH THIS PROGRAM BUILD CANNOT BE READ WITH PREVIOUS BUILDS. THE TRANSMITTER DATA WILL NOT BE AVAILABLE
The Composite Reports now includes an option to print the profile in either landscape or portrait orientation.
Major revisions to Adaptive modulation specifications and operation. Refer to data_files.pdf in the DOC folder in the Pathloss program folder.
Automatic frequency design operation reworked. Assignments can now add ATPC from radio file or user specified value.
Single site interference analysis added to the program. Right click on a site legend after performing interference calculation to access this feature.
Link CSV report did handle thematics correctly.
Interference calculations with passive repeaters has been corrected.
The High Low Violation report can be printed if there are no interference cases
On microwave radio data file imports, the default BER has been changed back to the 10-6 value
Pathloss 5 - revision date April 4, 2012
Corrected a bug in automatic frequency assignment feature, which could incorrectly assign frequencies after changing the working group.
Minor improvements to the CSV Link report.
Area study dialog - Propagation parameters: the location variability was not being calculated properly. This could lead to corrupted CtoI coverage plots.
Pathloss 5 - revision date March 28, 2012
Area study dialog - Propagation parameters: the location variability was not being calculated properly. This could lead to corrupted CtoI coverage plots.
Frequency assignment - In some cases if a profile has been reversed, the Hi-Lo channels could be applied to the wrong sides of the link.
Reflective plane analysis - when using the diversity planning feature, the disabled edit box will now show the height of the TX antenna. The active edit box will show the height of the diversity receive antenna.
A bug in the Auto link design dialogs regarding the Availability and Unavailability rejection criteria has been fixed.
Pathloss 5 - revision date March 8, 2012
Bug fixes regarding CSV Link report and Auto design operations.
Pathloss 5 - revision date March 7, 2012
Export CSV file
The link and site thematic settings can be exported. This includes site type and status, link type and status and the LOS status. These are exported as integers in the range 0 to 8 and and a description corresponding to the thematic settings in the Network display.
Note that thematics are not exported with transmission detail or summary reports.
BIL projected DEM index text import
A UTM zone column assignment if the DEM is set to a variable zone projection.
Interference Calculations
Some cases of older version 4 radio data files with incorrectly formatted transmitter spectrum curves have been encountered. When these files were used to calculate filter improvement by integrating the TX emission into a receiver selectivity curve, the resulting filter improvement was negligible
Dispersive fade margin and equipment signature in adaptive modulation radios These parameters were not used in the overall availability calculations
Pathloss 5 - revision date February 23, 2012
On composite reports the path profile has been rotated to a landscape format.
A 36 dBi EIRP limit has been added for the ISM bands 902 to 928, 2400 to 2483.5 and þ5725 to 5875 MHz
Operations carried out in the network display while a link was open in the PL50L Link Design window could cause the frequency and other options of the PL50L link to change. These operations included the Import Pathloss data files and the automated design operations.
The fix allows you to import Pathloss files while a link design window is open. The automated design operations now demand that an existing PL50L link design window must be closed.
Pathloss 5 - revision date February 15, 2012
Report printing revisions will be carried out over the next several months. The present build allows a selected area of the network display to printed. The direct to printer option now includes scale printing on one or more pages.
Pathloss 5 - revision date February 9, 2012
Important notice for Pathloss 5 users
License server IP address changed, Versions of Pathloss 5 earlier than this will not be able to use the online activation features.
Vector .map files containing text and point format data can now be loaded and displayed. Line colors included in vector .map files are now displayed.
All extents, layers and transparancy settings are now saved and loaded with the network file.
Reflective plane analysis window could display anomalous values in the disabled edit controls when using the space diversity planning options
Pathloss 5 - revision date January 23, 2012
Minor bug fixes.
Pathloss 5 - revision date January 19, 2012
On adaptive modulation systems using the dispersive fade margin values, the dispersive fade occurrence factor was not available in the path parameters data entry form.
Terrain roughness - Vigants Barnett
The terrain roughness calculation methods are now available in the calculation options (default - design rules and pl5 files). The specific options are Reference - either sea level or a least squares fit to the terrain. This applies to both the automatic and user defined end point calculations. Terrain extents - The automatic calculation first determined the extent of the terrain which in intervisible to both antennas. If this extent is less than 50% of the profile, the central 80% of the profile is used. An option has been added to only use the central 80%.
Interference calculations
A high low violation report could not be printed if there were no interference cases. This restriction has been removed.
The update threshold degradation in pl5 files did not consider interference cases which had been set to "ignored" in the case detail report.
Link labels
The labels on north south links could be reversed under some conditions.
Pathloss 5 - revision date January 4, 2012
Rain attenuation at very high frequencies (75,000 MHz) - Crane model The algorithm did not extrapolate the rain curve if the lowest rain rate in the file produced an attenuation greater than the fade margin.
Pathloss 5 - revision date December 16, 2011
Minor corrections made to MapInfo vector tab files loading and site - links exports to MapInfo.
Diffraction design section
A variable parameter calculation on certain paths could place the diffraction module in to an unstable state.
PL5 file names generated automatically from the site names could sometimes fail if the site name contained backslashes.
Interference calculations file save and load could fail under some circumstances.
Pathloss 5 - revision date November 17, 2011
Diffraction Module: Running a variable calculation on certain paths could place the diffraction module in to an unstable state.
File names generated automatically from site names could sometimes fail if the site name contained backslashes.
Fixed bug that would cause interference calculations loaded from a file to become corrupted.
Pathloss 5 - revision date October 21, 2011
The frequency diversity improvement factor and channel separation were not shown in reports unless space diversity was also used.
Tower height with app did did not change when the units were switched between metric and imperial.
Area roughness was being converted under some conditions when the units were switched between metric and imperial. This affects the ITU-530-9/12 and the ITU-530-13 algorithms. Area roughness is only expressed in meters.
Rejection criteria in the automatic link design operations could vanish after entering then exiting the Link design rules section.
Path profile reports
The profile report will now show the fixed height under the following conditions :
- The Use clearance criteria option must be checked.
- There is only one clearance criteria ( the second clearance criteria must be blank)
The fixed height is drawn as a dashed line using the calculation line color and line width.
The fixed height is drawn from the profile with the earth radius factor. If there are any trees on the path, they will be drawn on the profile.
In the antenna heights design section, the fixed height is added to the profile with the earth radius factor and any trees are on top of this.
Ant-Rad
Receive filter loss has been added to the space diversity ACU.
In the ACU section, the antenna types could not be set in the dropdown lists in the last three ACU definitions
Improved copy and paste operations have been implemented.
Importing radio curves from a text file would not save unless one of data entries was edited.
Pathloss 5 - revision date October 6, 2011
Print profile
Fixed height clearance criteria was not being displayed.
Antrad
Fixed bugs which would drop radio curves if they were imported from text files.
Pathloss 5 - revision date September 29, 2011
The transmission detail and transmission summary reports would crash for point to mulitpoint links when the Write TX channel assignments were used.
A scale has been added to the Network display. This is an option set under Configure - Options - Network Display Options - Axis / map grid.
Assigned antenna heights
Assigned antenna heights are now used in the Edit-Modify Links operation.
GIS Configuration - BIL projected DEM
An option has been added to import version 4 index files of the type ody_xxx.dat. The user must set the projection.
Transmission analysis summary and detail reports
An option has been provided to print the transmission analysis summary and detail reports in either the table style as in Version 4 or in the columnar format.
This option is set under the Configure - Options - Program options - Report layouts menu item. This option is available for microwave and land mobile applications and for adaptive modulation applications using the total time below level for rain and multipath fades.
Note that for adaptive modulation applications using the data throughput probability, the table style format is always used.
Program activation
An option is provided to re-activate the program when using a floating lock and the "No licenses available" error is issued.
Performance reports
In the G826 option the headers SESR, BBER and ERR were out of order in the performance report.
Grid Float Terrain data
Fixed a bug which caused the north edge to be set incorrectly when using header files of a certain format.
Callsign has been added to the csv reports produced by the automatic designer modules. (Create links, design links, edit-modify links.)
Pathloss 5 - revision date August 9, 2011
The radio data file format has been modified to include the following parameters in each modulation state for adaptive modulation radios:
- dispersive fade margin
- equipment signature
- maximum receive signal
The August 9 ant_rad utility is required to produce the radio files with these extensions.
The ITU quad diversity method using 4 receivers has been implemented.
Fixed serious bug in site text import routine that detected sites within .1 degree of each other as being the same site.
Modified report windows so that a new panel is always shown in the taskbar.
Pathloss 5 - revision date July 7, 2011
Site text import now allows you to 're-import' on top of an existing network for the purpose of updating some site information. Matching sites are detected based on Callsign and Coordinates. When a match is detected, the user is given the option to update the existing site, add the new site (possibly overlapping), or skip over importing that site.
The AntRad utility now supports Pathloss 4 Radio Data files.
Pathloss 5 - revision date June 16, 2011
Minor bug fixes.
Pathloss 5 - revision date June 2, 2011
Fixed bug that could cause reflective plane analysis to display in black and white on some systems.
GIS system now supports world files for backdrop imagery geographic information
The ANT_RAD.EXE program was revised to correct a potential problem in normalizing the transmission spectrum.
Pathloss 5 - revision date May 27, 2011
Activation key codes can now be obtained via a HTML web interface. The activation and deactivation dialog boxes have been updated with instructions on how to use this feature.
Fixed bug that prevented color coded design links from being displayed when using Edit-Modify links.
Pathloss 5 - revision date May 17, 2011
Bug that caused some local studies to not export properly to Google earth has been fixed.
Pathloss 5 - revision date May 12, 2011
NLCD files were missing from the update. This prevented Pathloss from saving or loading GIS files containing a NLCD 2001 configuration.
Fixed program crash when using stand-alone group visability dialog box. Updated support for backdrop images from the USGS Seamless Server.
Pathloss 5 - revision date May 10, 2011
A description of all clutter revisions made in this program build is available in the file clutter.pdf
Fixed bug introduced with the new clutter categories that could cause GIS files to save incorrectly or not save at all.
Group Manager allows you to choose "Sites with links" or "sites without links" in the "Add from source" drop down list in group manager.
Additional error handling add to the constant gradient trace for non line of sight paths and site 2 antenna height ranges which do not generate a minimum number of rays.
Fixed a bug that would report small values for KQ Factor as 0. Also fixed bug preventing KQ Factor from being accepted in to the reliability portion of the design rules.
Pathloss 5 - revision date April 27, 2011
Frequency and path length information is exported to google earth
Pathloss 5 - revision date April 20, 2011
Create point to point links
The progress display now shows the number of links and the remaining time to complete the operation.
Pathloss 5 - revision date April 12, 2011
Site Names now displayed on internal 3D Viewer.
Pathloss 5 - revision date April 8, 2011
Minor bug fix for ITU 530-13.
Pathloss 5 - revision date April 6, 2011
Group manager no longer repositions the display during use.
Updated Transmission Analysis display for adaptive modulation radios.
New report format for adaptive modulation radios implemented.
Pathloss 5 - revision date March 22, 2011
Transmission detail and summary reports format modified.
Transmission analysis display modified.
User interface update allowing dropdown lists to be opened with the keyboard in worksheets.
Pathloss 5 - revision date March 10, 2011
CSV reports have been modified to eliminate column synchronization problems.
Google earth displays modified to show the site marker at the tower height.
Pathloss 5 - revision date February 24, 2011
The interference error log on Vista and Windows 7 was virtualized and could not be directly read.
Emission designator did not transfer from the radio data file to the radio lookup table.
The view radio data from with the radio lookup table has been added
Land mobile CSV reports did not correctly write the calculations
Mark links and find links have been added to the link list.
Pathloss 5 - revision date February 16, 2011
This build includes major program revisions and additions including the ODBC interface. The documentation for the network display has been completely revised and expanded. This is available in both compiled HTML and PDF formats. Example files are available for the automated link design operations and local studies.
A new floating lock licensing option has been added to allow users to share a program more effectively. It is now possible to have multiple programs with different options all under the same serial numbers. A user can view the current usage status or these programs.
Pathloss 5 - revision date January 11, 2011
Clutter loss using a description only type data base (NLCD, GLCC) In local and area studies, the clutter loss at the remote site is calculated as follows:
A 200 meter exclusion zone is setup at the remote. The clutter heights on last 200 meters of the path profile are set to zero. The diffraction loss is calculated due terrain and clutter on this profile. The clutter loss in the immediate vicinity of the remote, is interpolated from Clutter loss definition table at the design frequency for the specific clutter type.
These losses appear to be excessive especially at the higher frequencies. As a result this procedure is now only applied if the remote antenna height is less than the clutter height. In addition the loss is scaled from the the full value for an antenna height equal to one half of the clutter height and zero when the antenna height is equal to the clutter height.
Pathloss 5 - revision date January 4, 2011
Summary of changes made in the interference calculations using TX emission (measured or masks) and RX selectivity curves (measured or masks)
The first change came in the August 26, 2010 build to handle a very narrow band interfering signals into a very wide band receiver. The numerical integration did not adequately detect the interference in the receive passband.
The second change occurred in the November 19, 2010 build to deal with RX selectivity data which covered a frequency range of +- 2000 MHz with 10 data points. In this case, an interpolation algorithm failed. A side effect of the changes in this build was a failure to correctly read ToI or IRF curves. This was corrected in the December 10, 2010 build.
As a result of these changes, special software was developed to test different radio data files against each other. The tests shown a discrepancy between the results using TX emission masks and measured data. This has been corrected in the present build.
Pathloss 5 - revision date November 12, 2010
Fixed another bug preventing clutter from being considered in area studies under certain conditions.
Fixed bug which prevented the profile from updating when individual clutter heights were edited at specific points.
Pathloss 5 - revision date November 9, 2010
Certain projection combination would prevent clutter from being considered in local and area studies.
Diffraction variable, raytrace variable, and reflective plane analysis windows could lose the control panel at the bottom. The bottom panel is now static and cannot be lost.
Pathloss 5 - revision date October 28, 2010
Changes to the network back-end dramatically reduces the amount of time it takes to add large numbers of links to the network as a batch. This affects importing links from pl5 data files, importing link text files, and creating links using the automatic designer.
Deleting multiple links from the link list was slow on very large networks. This has been corrected.
Fixed small error reporting bug in auto link designers.
"Yes to all" button added for overwrite confirmation when finalizing links from any of the the auto link designers.
When a clutter entry was deleted by entering a 0 in the height column, the clutter was not correctly deleted.
To delete multiple clutter points, hilite the points by clicking in the leftmost column. Use shift and ctrl to create the selection. Then click F6 or Ctrl-Y. You have the option of deleting the points or just the clutter.
Mark site function in the site list will now cause the network display to center on the marked site(s) once you close the sitelist window.
Area studies can now be created with a maximum radius.
Area studies showing CtoI can now restrict which base stations are considered as carriers.
All Study displays can now be exported to vector formats (shapefile and mid/mif). Improved memory management in export routine.
Resolved bug which occasionally failed to set the correct delimiter on entry in to the text import dialog box.
Find function added to the site list.
Error handling on create p2p link design improved. Errors are compiled and shown in notepad at the conclusion of the operation rather than one at a time as they occur.
Pathloss 5 - revision date October 5, 2010
Improvements to the area study back-end drastically reduces memory requirements for studies involving a large number of base stations. Area studies can now be created on geographic geo-referenced backdrops. Area studies can be exported to Google earth from geographic geo-referenced backdrops.
Fixed crash which would occur when exporting a network with a large number of links to Google earth.
In Development: An area study showing C to I or simulcast delay can not yet be exported to vector formats (shapefile, mid/mif)
Pathloss 5 - revision date September 20, 2010
Corrected bug which caused the minimum value of K to always be reported as 0.05
Program could hang on newer operating systems while defining a polygon for an area study. The problem was similar to an earlier bug involving click and drag operations. A minor change to how a polygon is defined has removed the bug.
Pathloss 5 - revision date August 25, 2010
It was possible to perform an empirical study before setting the basestation and mobile antenna heights. Because these values are required for some studies the study data could become corrupted leading to display problems.
An Interference calculation using the auto OHloss calculation option would crash if there were any errors in profile generation.
Pathloss 5 - revision date August 19, 2010
The pl50 program would crash upon shutdown if the last site edited from the edit site dialog contained a basestation.
The Local Study would not always use the secondary terrain database if the basestation was located within the primary database bounds but the radius extended in to the secondary.
Pathloss 5 - revision date August 10, 2010
Area study
CtoI calculations in an area display analysis did not consider the antenna radiation pattern of the remote site.
ITU-530-12 - ITU-530-13
Switching between these two algorithms did not automatically recalculate the results.
Pathloss 5 - revision date August 6, 2010
There is a new option in the local studies display criteria that applies to the Line of Sight display. Previously, in an area where two or more studies overlap, a cell was marked as visible if ANY base station had LOS to that cell. You can now choose to have cells in overlapping regions marked as visible only if EVERY base station has LOS to that cell.
Local studies using the LOS criteria were not exported properly to google earth using the single image option.
Pathloss 5 - revision date July 26, 2010
Program stability issues
Certain mouse operations such as linking two sites together could cause the program to hang for no apparent reason. This behavior was rarely seen on Windows XP; however on Windows Vista and 7 the occurrence was more frequent. Note that this was not a crash but more of a "program not responding" issue. We believe that we have solved this problem in the current build.
Turing on or off individual local studies using the checkmark in the sitelist could lead to an incorrect display or program crash.
Pathloss 5 - revision date July 20, 2010
The maximum receive signal was not loaded into the lookup table from the radio index. The maximum receive signnal was also not loaded in to the Link design design rules from the lookup table. Both these problems have been fixed.
Installation help has been added to the PL50 menu bar.
Selecting the last row in the site list could cause a crash with some operations. The last row can no longer be selected in any grid controls.
Crane rain data entry form
If the cancel button was clicked, the "Rain calculation" option was always set to off and the polarization was set to horizontal. The ITU rain data entry form operated correctly.
Radio and Antenna Index
The column sort order is retained for the session
Elevation Backdrop
Per pixel transparency has now been added to the elevation backdrop. This makes possible such effects as show only elevations in a certain range or one color elevation displays.
In some cases, if a list contained a very large number of items, the vertical scroll bar would malfunction when being dragged.
Local Studies
- Fixed bug in which local studies with different cell sizes would not be properly displayed together.
- Local Studies are now supported when using a geo-referenced backdrop with a geographic projection.
- Similar updates to area studies coming soon.
Pathloss 5 - revision date June 29, 2010
Studies
Area studies could crash for the C/I display criteria for some polygon shapes.
Error handling in both area and local studies for missing files could cause a program crash.
When both an area study and a local study were displayed using the same criteria, changing the colors and ranges for one study did not automatically update the other study
Radio Lookup Tables
When the radio index was used to populate the radio lookup table, the dispersive fade margin was not added.
Radio and Antenna Index
Both the hi frequency and the low frequency were required for the filter to operate correctly.
Pathloss 5 - revision date June 8, 2010
When a Pathloss data file which includes a passive repeater was loaded, the end site azimuths were recalculated incorrectly.
Pathloss 5 - revision date May 12, 2010
Improvements to local study memory management for very large studies.
ITU 530-13 mutipath fade algorithm added.
Pathloss 5 - revision date May 4, 2010
Path inclination was not automatically updated for antenna height changes in the antenna heights design section or the Configure - Antenna Heights menu selection.
The diffraction reports did not print when the diffraction calculations were carried out using any of the automatic design features.
Added functionality that allows multiple local studies to be defined as a batch. Selecting the menu item Studies->Local Studies->Batch Define will bring up a dialog box to set the study parameters. You can use a selection or group to control the base stations for which the studies will be defined. Only fully defined base stations will be included in the operation, and existing local studies will not be affected. When the studies have been defined select menu item Studies->Local Studies->Batch Generate to generate all the studies. (This may take some time for large areas.)
CDED file index
Created an index from converted CDED files did not properly set the file directory.
Reflection Analysis - Space diversity planning
The space diversity planning is only applicable for the TRDR-TRDR antenna configuration and the earth radius factor variable parameter. The space diversity planning is not inhibited if these two conditions are not met.
KML export
Google Earth does not allow the character '&' to be used in a site name. This check has been implemented in this program build
Pathloss 5 - revision date April 27, 2010
Options have been rearranged in to 3 categories that better reflect their scope and usage.
- Network Display Options control the appearance of the network in PL50.
- Program Options are options that apply to the entire program (report formats for example) and are saved in the ini file.
- Calculation options apply to a single link or design rule file depending on where the options are accessed from. A line in the options dialog states exactly how the options are being applied.
Links can be now be added to groups based on Application Type. Click on Configure - Group Manager and then select the Add on condition feature. Select the check box and set the application type in the drop down list. When you click the check box, all links of that type will be added to the group.
Thematic site and link status color will now override the site and link colors even if there is no thematic type defined.
Fixed bug that prevented clutter backdrop from displaying if the definition window was not opened. This applies when the definition is loaded automatically from .grc files.
Report file names are now initialized to null and must be provided by the user at the time they are saved.
Pathloss 5 - revision date April 13, 2010
The copy function has been updated to allow for the copying of study and elevation legends as well as high resolution backdrop images. The copy function can be accessed from the main menu under File->Print->Copy or from the toolbar icon. The dialog allows you to select which element you wish to copy to the clipboard as well as specify a resolution multiplier.
The resolution multiplier applies when you are copying a network display containing bitmap elements such as backdrop imagery and studies. It allows you to retain higher image resolution even if the image is zoomed out in the display. The higher the multiplier, the greater the image resolution.
Using these methods you can make consecutive pastes in to vector or word processing software to build a network picture with legends. Note that because the clipboard data includes vectors as well as raster information, the behavior when pasting in to image editing software may vary.
Network printing is still in development and more features will be added in future updates.
Pathloss 5 - revision date March 24, 2010
Diffraction calculations
Corrected an error in the March 17 build which caused a program crash.
Network Display
The status bar now contains the measurement units (kilometers-meters) or (miles-feet). Click on this button to convert between the two systems
Pathloss 5 - revision date March 17, 2010
The Copy/Move network operation is now able to use groups and selections to limit which files will be copied. The network will still retain all the links but only the link files in the selection or group will be copied. Any link files that are not copied will no longer be referenced by the gr5 network.
GIS Configuration
Indexing for NLCD clutter can now be carried out for complete folders and sub folders. In the File index display, click Files - Import index - bil, hdr, blw folder- subfolder. Select the top folder containing these files to create the index.
Note that this procedure cannot differentiate between bil clutter files and bil dem files. Do not use this procedure if the folders contain both DEM and clutter files.
Elevation backdrops for transverse Mercator projections which included a latitude origin resulted in a distorted view. An example of this type of projection is the UK national grid.
Completed Local Studies are now saved to disk in a format that will allow faster loading.
Corrected a logic error that prevented the Secondary DEM from filling in any 'no data' patches left over from the primary DEM.
The active link (open in pl50l design window) is now highlighted in green on the network display.
Corrected bug causing variable zone projections with bounds to not display coordinates on the status bar or in Add Site dialog.
Can now access design modules via a menu in the link list.
Pathloss 5 - revision date March 2, 2010
Antenna beamwidth - downtilt
The multipath - reflections design section uses the elevation antenna 3 dB beamwidth and the antenna mechanical downtilt parameters in the analysis. Previously, copies of these variables were initially taken from the transmission analysis section and were not updated. The values are now the same in both design sections.
Antenna orientation calculations
These calculations are now continuously updated for all data entries and changes.
CSV reports
The delimiter selection (comma, tab, semicolon or other) now works. The text qualifier now allows a delimiter in an expression.
Pathloss 5 - revision date February 23, 2010
Create PTP/PTMP links - Design links - Edit modify links
The windows hierarchy in these functions could result in the current window being hidden.
Terrain data section
The survey angles function returns an error message if the cursor is on site 1 - the first point in the profile.
The single structure dialog warning message "Structure exists at this location" has been removed from the dialog. An error message will be generated if the user attempts to add a structure at a location where one already exists.
Multipath - Reflections
Under certain non line of sight conditions, the program would crash when the define plane function was called.
GIS configuration - Indexing NED bil files
This can now be carried out for complete folders and sub folders. In the File index display, click Files - Import index - bil, hdr, blw folder- subfolder. Select the top folder containing these files to create the index.
Pathloss 5 - revision date February 8, 2010
Google Earth Export
Local and area studies are now reprojected from the network display projection to the Google Earth plat carree projection. This improves the positioning within Google Earth, especially for large areas.
Local and Area Studies
If the variables "show local study" or "show area study" are changed in the site list, the changes did not take effect until the local or area study was regenerated. In this program build the changes will take effect immediately when the site list is closed.
Interference case detail report
The delete case and delete subcase buttons in the case detail report would cause a crash whenever all subcases associated with a receiver were deleted
Radio Lookup table
The second time the radio lookup table was accessed, the radio data would not be added if the design section had changed between accesses.
Local studies did not export to Google Earth unless all options were selected
Pathloss 5 - revision date January 20, 2010
Diffraction
If the diffraction algorithm was set in the PL50L program options, the tool bar in the the diffraction section was not reset.
Switching diffraction algorithms in the diffraction section, did not completely reset the calculations resulting in some interaction between algorithms.
Fixed bug in ray trace and reference plane analysis which would not show colors when printed in a batch report.
Pathloss 5 - revision date January 13, 2010
Diffraction loss
Reflective plane definition for Longley and Rice algorithm revised for line of sight applications.
Interactions between the diffraction loss calculations carried out in the transmission analysis section and the diffraction section have been eliminated
Pathloss 5 - revision date January 4, 2010
Some stability problems have been corrected in the link text import. If a file could not be saved, an error report is written and displayed at the end of the import.
Reflection plane report crash.
Import text files
The settings and column definitions can be saved and loaded. This makes it possible to handle any number of column definition formats for a particular import.
Pathloss 5 - revision date December 23, 2009
New menu item Assign Thematics under the Operations menu in PL50 allows thematics (site Type, site Status, link type, link status and los status) to be assigned to a selection or group.
Exporting to Google Earth now allows the local studies to be exported as a single image rather than an image for each base station. This option is shown on the export dialog.
Exporting PL5 to PL4 was missing the traffic code. This has been fixed
Pathloss 5 - revision date December 17, 2009
Fixed bug which caused local studies to have erroneous loss if clutter files could not be found.
Fixed some minor visibility problems regarding local studies.
GIS configuration
If a vector file (MapInfo or Shapefile) with building elevations was entered in the vector tab file list, then the program would crash when the file list was opened and the vector file was not at the specified location.
Grid ASCII conversion
Improved error detection in grid ascii file
3D terrain view
The user interface has been redesigned.
Update pl5 files
This function in the site data list will set the profile end point elevations to the values specified in the site list.
Automatic OHLOSS calculations in an interference calculation
If the "Calculate OHLOSS automatically" option was checked in an interference calculation, the program calculated the OHLOSS for each case. If the addition of the OHLOSS resulted in an interfering signal less than the objective minus the margin, the interference case was discarded. In all other cases the reports showed the OHLOSS being included twice.
Radio and antenna lookup tables
For antenna, the model and gain are the minimum requirements For radio lookup tables, the model transmit power and receive sensitivity are the minimum requirements. Minor reformatting changes were carried out to these tables.
Import link text file
A csv file with more than 2048 characters per line would cause a program crash. Any line length can now be used.
Pathloss 5 - revision date December 02, 2009
Visibility of ungrouped sites and links is saved in the gr5 file.
Export to shapefile and mapinfo mid/mif now allows export of groups or selections. More information exported to shapefile and mapinfo mid/mif databases.
3D Display now only shows visible network.
Fixed error exporting studies to google earth from certain datums.
Refinements to google earth export: More information in description, links now shown above ground at antenna height.
Pathloss 5 - revision date November 25, 2009
Export to google earth now allows export of groups or selection.
Maximum receive signal exceeded has been added to the trasmission analysis warnings.
More information is exported to mapinfo mid/mif format.
Pathloss 5 - revision date November 17, 2009
Profile displays now show the arrow on top of any structure or clutter at the selected point.
The excess clearance display in the antenna heights design section showed the longitude hemisphere incorrectly.
Erroneous base station circulator branching loss values could be generated if the Cancel (red X) button was clicked in the antenna coupling unit data entry form.
Create P2P links. Joining a group (or selection) to all sites now works as it should. Previously, some links between group members were omitted.
Pathloss 5 - revision date November 10, 2009
Create P2P links
Joining a group (or selection) to all sites now works as it should. Previously, some links between group members were ommited.
Hot keys have been added to switch between the link design sections.
Manual site linking direction Manual links were created in west to east direction. Links which were exactly north - south were created in a south to north direction. Using this convention, all profile displays had the westerly site on the left side.
This has been changed so that the first site selected is always on left side of profile displays.
Link text file import If the design frequency is not available in the import, the average channel assignments are now used.
Print profile options
The print profile options were not saved on exiting the report printing dialog.
Pathloss 5 - revision date October 20, 2009
Fixed crash involving Ohloss and Diffraction Loss Reports.
Pathloss 5 - revision date October 15, 2009
GIS Configuration
ESRI header files used for indexing BIL files with out a corresponding prj file are now supported. The projection information is contained in the hdr file. The user must set the projection.
CSV Import
The duplicate column assignments error message now identifies the specific column numbers and in the case of the "Site text file" import, the field name is specified.
The link text import loads the antenna code if available.
Pathloss 5 - revision date October 5, 2009
Rain data files
City rain data files have been added to the program. These are non proprietary rain files for US and Canadian cities.
Provision has been made to use the Proprietary ATT radio data files; however these are not supplied with the program. These files must be located in the directory geo_data\rain\alu_rain.
Radio and Antenna Code Index
Improved functionality for the find control.
Pathloss 5 - revision date September 29, 2009
Link Text Import
Coordinates using separate columns for degrees, minutes and seconds were not importing correctly.
Station, owner and operator codes
These site specific parameters can be used for alternate data storage and status information. These parameters can be excluded from the network
- pl5 file discrepancy checking. Click Configure - PL50 Program options
- Network link data checks to set these options.
Link design rules
Field margin has been added to the link design rules. The data entry is in the reliability parameters section of the design rules dialog.
Radio and antenna code data entry.
These can now be entered directly and deleted in the respective data entry forms.
Tooltips have been added to the radio and antenna indexes.
Antenna clearance report
If the controlling clearance criteria included a fixed height, the clearance report did not included this fixed height.
GIS Configuration
If the vector tab included shapefile definitions, and the shapefiles were not present, the program could crash on startup.
Pathloss 5 - revision date September 24, 2009
Backdrops
The Import Index - Mapinfo tab file option now supports bmp, jpg, and png in addition to tif as image formats. One bit black and white tif files are now supported.
Link text file import
Multiple links between the same two sites can now be carried out in the link text file import
Pathloss 5 - revision date September 22, 2009
Vertical Mapper Clutter files (gcd files)
Clutter data in the MapInfo vertical mapper format may include a clutter definition table in the file. If this exists the data will be automatically entered into the clutter definition table.
Note that clutter elevations do not exist in this file format. All clutter elevations have been set to a default value of zero. It is the users responsibility to assign the clutter heights. The clutter cross reference categories have been set to an "open land" default value. For local and area studies, the user must assign the cross references
GIS Configuration
The Philippine reference system 1992 datum has been added. This is effectively the same definition as the existing Luzon datum, however the transformation to WGS84 utilizes the 7 parameter algorithm for the entire country, whereas the the Luzon definition uses a 3 parameter transformation and two regions (Philippines excluding Mindanao and Mindanao) The Philippine transverse mercator projection for the five zones has been added for this datum
The clutter definition table now shows the clutter elevations in the units currently selected (feet or meters). Previously units were always in meters
Interference case detail report
Headers in the performance degradation did not line up with the actual data.
PL50L Options
The automatic diffraction algorithm selection (Pathloss, Tirem or NSMA) was not included in the PL50L option settings
Obstruction Fading (transmission analysis section) The diffraction loss iterations could fail under certain conditions and return a critical value of K of 1.33. The results were completely unrealistic
Pathloss 5 - revision date September 15, 2009
Passive repeaters
Passive repeaters created in the network display had stability problems.
Vectors
Added support for displaying ESRI shapefiles of type SHPT_ARCZ and SHPT_POLYGONZ.
Backdrop Files
MapInfo tab files can be loaded directly in to the Backdrop index. This is a multiselect operation. If the list is empty, then the first file added sets the projection. All successive files must match this projection. If the index contains any entries, then the existing projection determines if the file can be accepted.
Update PL5 file in the network display only updated one site in a link if the YES button was clicked. The Yes to all button operated correctly.
GRIDASCII
Converting a GRIDASCII resulted in a "File format error" on UNIX files. The program incorrectly interpreted the 0xA end of line character.
Pathloss 5 - revision date September 8, 2009
Set GIS configuration The MapInfo derived projection could cause a program crash if it was manually selected from the projection drop down list.
The ERP values in watts and dBm were reversed in land mobile applications in the transmission analysis display.
Diffraction loss
The diffraction loss calculation failed on line of sight paths with more than 6 terrain incursions into the 60% Fresnel zone radius.
Pathloss 5 - revision date September 2, 2009
Vertical mapper grd DEM files using 16 bit integers were not correctly read.
Pathloss 5 - revision date September 1, 2009
Link text file import
If the design frequency is not specified, and channel frequency assignments are in the file, then the design frequency will be set to the average of the channel frequencies.
Define plane
The define plane caused a crash when switching between the manual and automatic generation methods
The network file consisted of two files with the suffixes gr5 and gr5ids. The gr5ids contains the site and link ids and is intended to be used on a shared file basis. The gr5ids file has been removed in this program build due to potential data synchronization problems.
Rain errors were reported even when the rain calculation was switched off.
The free space loss formula gave results which were 0.02 dB different than the version 4.0 results. This small difference created difficulties in comparing availability results which are formatted to five decimal places. This release changes the free space loss to the version 4 formula.
Pathloss 5 - revision date August 26, 2009
Minor fixes to radio and antenna lookup tables.
Pathloss 5 - revision date August 25, 2009
Pl50 Options
Site Attributes, Site Label, Link Attributes and Link Labels can now be applied to a group or selection.
Set GIS Configuration
The File index for NLCD2001 clutter did not show the clutter name on the caption
PL40 radome loss
When a pl4 file containing a valid antenna code was opened in the standalone PL50L application, the antenna data was reloaded. This caused the radome loss to reset.
Space diversity - IF combining - corrected.
Changed gr5 save routine to guard against header errors.
Pathloss 5 - revision date August 17, 2009
Transmission summary report when invoked from the transmission analysis menu bar always showed the distance and elevation in Miles / feet
Network to PL5 discrepancy dialog. Direction arrow buttons did not function.
Pathloss 5 - revision date August 13, 2009
Network display - Map crossings
The map crossing function has been implemented. This is only valid for the default network projection. First set the axis to correspond to the desired maps (Click configure - PL50 options - axis-map grid). Then right click on the link and select map crossings. If the US 1:24,000 7.5 minute map scale has been selected, the report will show the actual map names.
Terrain data module
The reverse profile did not reverse the site names on the status bar.
Fixed google earth datum transformation.
Fixed minor bugs related to the no data entries in clutter databases.
Pathloss 5 - revision date August 6, 2009
Group manager
The visibility display rules have been changed to allow a group containing only links to be displayed. Some fixes have been made involving operations where some sites and links are hidden.
Antenna heights section
The graphical antenna heights display now does not show the minimum clearance criteria. Previously this was show as a modification to the Fresnel zone radius. Although the results were correct, this display was somewhat confusing.
The minimum clearance criteria is intended to provide clearance for close in obstructions where K and the Fresnel zone radius are very small and can lead to a grazing path. Note that when this is specified, the antenna heights cannot be less than this value.
Radio data entry form (Adaptive modulation)
Clicking the blue button to access the adaptive modulation table, could bring up a second instance of the table which could cause a program crash.
Update PL5 files has been added. This function is available on the site list menu bar. The procedure checks all associated pl5 files and compares the site data to the data in the site list. If there are any differences the user is prompted to modify the pl5 file. This is a one direction change - Network site data to pl5 file.
Pathloss 5 - revision date July 31, 2009
NLCD2001 and NCLD2002 clutter data downloads in BIL format from the USGS site are now working. These files can be used with the July 31, 2009 program build.
NED and SRTM elevation data downloads in BIL format are now in a 32 bit floating point format. We believe that this is an error as the definition of the BIL format on the USGS site states that the elevations are in a signed 16 bit integer format. The new float files are twice the size of the integer files.
The July 31, 2009 program build will read the floating point files.
The Group manager operation has been revised so that links can exist in a group without the associated sites being in the group. This allows the user to create a group with links only or with sites only. Combinations of sites and links in a group are still possible. In this arrangement, links can now be hidden without hiding the sites.
Printing and copying the network display with backdrops produced black ares where the backdrop was missing.
Pathloss 5 - revision date July 29, 2009
Site list does not reset display unless coordinates are changed.
Set GIS Configuration correctly recognizes when the projection of the display has changed.
Pl5 Link Files deleted by Pathloss are now sent to the recycle bin rather than being permanently deleted.
Reports
Fixed bugs causing columns to be out of sync and filenames to not be displayed in some cases.
Antenna Usage is shown next to the antenna model in the transmission detail and transmission summary reports.
Point to point link design
The antenna coupling unit (ACU) data entry form in the base station definition did not match up with the ACU data entry in the Link Design Rules. These are now exactly the same interface
Pathloss 5 - revision date July 24, 2009
The addition of new fields to site data caused a crash in the site data entry forms.
Fixed error in which a group could become corrupted when importing from site text files.
Pathloss 5 - revision date July 22, 2009
Obstruction Fading
A preliminary implementation is available in the transmission analysis design section. Click Operations - Obstruction fading. The next program build will include the documentation and the obstruction fading will be incorporated into the reports
Local and area studies
The receive at base station option cause an error.
CSV link report
The antenna usage field has been added. This will only appear if the antenna model is checked.
Import text links
Quotation marks were not automatically removed.
A preliminary request for frequency coordination CSV report has been added. Click Operations - Frequency Coordination report. The report format may change based on discussions with Alcatel and Comsearch. The following fields have been added to the site data structure for this report.
- Antenna registration number char[16]
- Zip code char[16]
- Tower height with Appurtenances
Under some circumstances - distance, azimuth and projected coordinates were not automatically calculated from the site coordinates.
Pathloss 5 - revision date July 9, 2009
ASTER GeoTiff Data
Support for the ASTER geotiff terrain elevation data has been added. This is a one arc second data base with global coverage over the latitude range 83N to 83S. This has been implemented as a BIL geographic DEM.
Radio and Antenna Cross Reference
The radio and antenna cross reference in the link text file import has been implemented. Note that at this time there is no check on the code validity and the codes are not expanded to complete missing data entries.
Antenna lookup tables
The default antenna lookup table was not loaded on startup.
Pathloss 5 - revision date July 3, 2009
Site text import
Site elevation values were corrupted in the import procedure.
Local studies
The climate region was was not being updated in both local and area studies. A continental temperate climate was used in all cases.
Network
The move site operation did not update the azimuths in any associated pl5 files. Move site can be potentially dangerous. Additional work is underway to advise users of the full impact of the site move operation.
Pathloss 5 - revision date July 2, 2009
The options dialog in the transmission analysis section was missing. This dialog allows the entry of water vapor density in microwave - adaptive modulation applications and the location selection for land mobile applications
Time variability was not being updated in both local and area studies. A constant time variability of 50% was being used.
Auto link design on PTMP links using all sites within a specified radius, did not consider the visibility state of the sites.
Pathloss 5 - revision date June 30, 2009
Group manager
The user interface for editing groups as a list has been completely revised. The group visibility interface has also been revised.
Adaptive modulation
The percent of time in mode is now show for the total annual throughput.
CSV Link Report
The options for Transmission detail and Transmission summary were reversed. Site coordinates were only exported in degrees minutes and seconds format. The decimal degree option now works.
Reflective plane definition
Continued resetting and redefining a reflective plane could cause a program crash.
Pathloss 5 - revision date June 22, 2009
Assigned antenna height
The import site text file (csv) now includes an assigned antenna height field. The value is not displayed in the site list display. Click Edit - Edit item to view all fields in the site list including the assigned antenna height. This field is used in the following auto-design operations:
create PTP links create PTMP links design links (PTP and PTMP)
The Link design rules includes the option "Use assigned antenna heights" in the Antenna heights - tx lines setting. When this option is checked, the assigned value for a site will be used in all links from that site. If there is no value for the assigned antenna height, the tower height will be used. If both the assigned antenna height and tower height are not available, the site will not be used in the design operation.
Use the "Clearance" display criteria to display the results of the design operation using the assigned antenna heights.
PL4 files can be exported using group or selection directly from the Network display.
The clearance criteria used in the link design rules were not saved once the session was closed.
Radio and antenna lookup tables
If the default lookup table file cannot be found, the program would crash. The antenna lookup table high and low frequency values did not sort correctly.
GIS setup
Clutter index for was not saved correctly under certain conditions.
Pathloss 5 - revision date June 15, 2009
Set GIS Configuration
The default directory specification has been changed from a single directory to individual file directories when importing an index.
Some procedures involving lookup tables and code indexes, could cause the data entry form to loose focus and go behind the network display.
Import link text file
This procedure has been revised to include 3 antennas and 12 TX channel entries. Still outstanding are the cross references between the radio and antenna codes in the csv file and the actual codes to be used.
Pathloss 5 - revision date May 26, 2009
The Design link function has been completely revised and divided into two functions. The Design links function only operates on links without a pl5 file association. The Edit-Modify links function only operates on links with an existing pl5 file association.
Network Operations
The following side effects introduced in the due to the May 19 build have been corrected The Performance function caused a program crash The Add site and Move site dialogs sizes were not usable
Rain calculations
The ITU-R P.837-5 rain data base has been added to the program. The original 837-3 has not been removed. It should be noted that the difference can be significant between the two data bases.
ATT rain data files for the United States are not distributed with the program. The directory geo_data\rain\rain_usa contains Canadian rain data files in the ATT file format. The file naming convention is CURVEXX.CSV where XX is a one or two digit number. If the USA files are located in this directory, then they will be automatically used for the Crane rain algorithm
Antenna Lookup Tables
Radome loss and antenna diameter have been added to the lookup table
Radio and antenna data lookup files could cause a program crash if an arbitrary file was loaded.
Ant_rad.exe - radio data files
If a binary radio data file was saved several times in a row, the calculated curves - TX emission mask, RX selectivity mask and the RX selectivity curver used in calculations would be duplicated.
Pathloss 5 - revision date May 19, 2009
Design Links - Network Display
This has been completely revised. The operation is similar to the Create PTP / PTMP links feature.
It is possible simply to view the key performance indicators (KPIs) of the network links using either the original design rules or the current design rules.
A group selection criteria is provided to move the links into different groups based on these KPIs.
Transmission line lengths on PTMP link designs have been corrected
Data integrity checks between PL5 files and the network display. When a pl5 file was saved, the network display data was automatically updated to the PL5 data. This has been changed. If differences between the two data sets are present, the user is prompted to select the correct data.
MapInfo grc files (one byte data files) were not read correctly. These files were being used as clutter data.
Pathloss 5 - revision date May 7, 2009
Create PTP and PTMP links
Clearance has been added as a rejection criteria. This is the clearance relative to the clearance criteria. A value of 0 means that the clearance criteria has been exactly met. A positive value is the excess clearance over the clearance criteria. A negative value is the additional clearance required to meet the clearance criteria.
A minimum and maximum value can be specified for each rejection criteria. In addition, the current link display can be saved to a group. This makes it possible to save the analysis into multiple groups. For example the group names could be as follows:
clearance OK clearance within 10 meters clearance over 10 meters
The links can be saved with the original color legend.
Point to point equipment parameters now used the same standard data entry forms used in the transmission analysis section and include both lookup tables and the radio - antenna indexes.
Automatic Link Design
Diffraction loss is calculated at three values of K (4/3, the minimum expected value of K and a K of infinity). The infinity value was used in the transmission analysis under the assumption that heavy multipath fading is coincident with high values of K.
In this program build, the 4/3 value is used. Future program builds will expand on this and provide the probability of obstruction fading.
Lookup tables
Various data entry and conversion problems with antenna and radio data lookup tables were corrected dbm to microvolt conversion on the land mobile radio data entry form did not operate.
Pathloss 5 - revision date April 22, 2009
Multipath - reflection
Variable parameters calculations using ray tracing did not correctly save in the pl5 file.
Variable parameters calculations using ray tracing on paths which were blocked at the lowest value of the earth radius factor K could cause a program crash.
Transmission analysis
The vertical angle and azimuth were expressed as degrees minutes and seconds in report. The vertical angles were reported as positive values. These are now expressed as decimal degrees with the correct sign
The report format options for microwave total time below level showed the annual rain unavailability and the total annual rain + multipath unavailability in expressed in seconds. The actual report expresses the value in minutes. This provides compatibility with ITU conventions of expressing unavailability in minutes.
Loading a radio data file could could change several of the calculations options. These changes have been inhibited for the time being. The radio data files contain calculation methods such as selective outage and performance calculations in accordance with G826. A future release will prompt the user to make these changes and the changes will be immediately reflected in the radio data entry form.
FCC EIRP warnings were based on dBm instead of dBW
Vectors
A side effect of continuing development on shapefile features resulted in program crash when using vector shapefiles
Network display link list
If the link list was closed with the last row selected, the program would crash
Pathloss 5 - revision date March 26, 2009
Site list
Corrections made to the import/export CSV files operations.
Corrections made to column sorting.
Automatic link design
Antenna height greater than the tower height link rejection criteria has been added.
Tower heights have been added to the CSV report.
Finalize links did not correctly limit antenna heights to the tower heights
Diffraction module
Under some circumstances Fresnel zones could not be displayed.
Reports
This section is now under revision. The version 4 print profile report has been added.
Pathloss 5 - revision date March 10, 2009
Radio lookup tables can load version 4 microwave (mrd) and VHF-UHF (vrd) lookup files.
CSV Link reports have been added. They can be found under the Operations menu in the network display. The report can be customized by clicking the 'Edit' button and selecting CSV Link report from the dropdown list in the report settings window. (More report settings are available in the tree list on the left.)
Pathloss 5 - revision date February 24, 2009
Radio lookup tables
This has been added as an option to using the radio code index. If a code exists in the table, the, lookup table functions the same as the radio code index.
Other fixes
Loading pl4 files which contained Fresnel references became corrupted when saved as PL5 files.
Interference calculations for base stations without associated links has been implemented.
Pathloss 5 - revision date February 12, 2009
Base station sector frequency assignments
The TX channel table and frequency plan files are now used for frequency assignments.
Point to multipoint design
The base antenna height is not considered in the rejection criteria.
Google Earth kml export
General improvements to the overall display. Local and area studies are now exported as separate entities for each signal level.
Other fixes
Metric conversion problems - (feet and miles only).
Error in transmission line unit loss in ptmp link design corrected.
Error in tower heights corrected.
